Customer Project: Nate’s Wind Turbine System in West Texas

Wind Turbine Customer Project

Nate’s 7 Blade Missouri General Freedom II Wind Turbine System and Adjustable Wind Turbine Roof Mount

Nate sent us a couple of photos of his wind turbine and all in one charge controller board setup after a quick two day install at his mom’s house.  To install the wind turbine, he used our adjustable roof top mounting system.

Here is a picture of the finished wind turbine system, installed on the roof.

Missouri Wind 7 Blade Freedom II Wind Turbine

Missouri Wind and Solar 7 Blade Freedom II Galvanized Wind Turbine mounted on a rooftop in West Texas

The electronics were installed inside to keep them protected from the elements.  Nate paired our All in One Charge Controller Board with Aims Inverter and a three phase brake switch for operation and maintenance.

To make things easy, he made sure to include simple labels to the different components for quick reference.  This clean install, in part to the pre-wired controller board, makes efficient use of the power generated by the wind turbine

All in One Charge Controller Board with 2000 Watt Power Inverter from Aims

Missouri Wind and Solar All in One Charge Controller Board with 2000 Watt Aims Inverter

To see the video of the wind turbine system in action, click here: Wind Turbine Rooftop Video

Products used in this customer project:


 

Customer Project: Hensley’s 11 Blade Freedom II Missouri Wind Turbine

Wind Turbine Customer Project

Hensley’s 11 Blade Freedom II Missouri Wind Turbine

Missouri Wind Review Freedom II PMG Wind Turbine


Hensley Isaac films his 11 Blade Missouri Wind and Solar Freedom II PMG Wind Turbine.


Hensley is located in Antigua where his wind turbine has withstood 88 MPH hurricane winds and provided power to his home when grid power was down.  The hot dipped galvanized and polished aluminum finish have also resisted rusting from the salt water which is an important factor for islanders looking for wind power.


He’s also installed an AcuRite  weather station to measure wind speed, direction, rainfall and temperature to help track the data on his wind turbine and solar panel hybrid power system.


Hybrid charge controller unit with built in dump load resistors


Click here to see Hensley’s full YouTube channel with more videos on his dump load, solar panels, micro grid tie inverters, etc.


 

Products Seen in This Video:

 


Watch a complete playlist of Missouri Wind and Solar Freedom and Freedom II Wind Turbine Video Reviews

Wind Turbine Troubleshooting

Wind Turbine Troubleshooting

Simple tips and methods for wind turbine troubleshooting.  Answers to common problems, advice for where to install your turbine, etc.

Testing Wind Turbine Output:

Do not use an AC voltmeter or ammeter for checking turbine output. Only check the wind turbine with a DC voltmeter and/or ammeter on the DC side of the rectifier. Our wind turbines may produce variable voltage. Only check the DC voltage of the turbine when it is disconnected from the battery bank and/or charge controller.

You can charge a battery or bank of batteries only if the wind turbine is producing more voltage than the battery’s voltage at that time. This will show up as amperage and most likely show a slow battery voltage increase. It is possible to see your battery’s voltage rise quickly with a strong gust of wind and then fall back down to the original voltage or just above the original voltage. This is normal because a battery is a large storage tank of energy and it takes time to fill with light to medium winds.

Make sure all electrical connections are clean and tight. If you are using the tower as part of the run of the negative output, make sure it has good, clean metal-to-metal contact with the housing of the PMA which is the negative side of the turbine.

Cable Size:

Do not use solid or undersized cable for the turbine’s power cord(s). Solid cable will not twist and flex well and is also a weaker conductor. Undersized power cable is subject to heat damage and will reduce power output substantially. Your power cable can be as large as you want.

Do not use outdoor extension cords, they do not stand up to wind turbine applications and are not designed for permanent outdoor use.

Blocking Diodes:

Our Freedom PMG and Freedom II PMG do not require blocking diodes. Blocking diodes reduce power output and are not needed after the bridge rectifier. In the DC models, the rectifier is built into the inside of the case.

Reducing Wind Turbine Noise and Vibration:

A slight hum may be normal from your turbine. If you have severe shaking with vibration, this usually means one or more blades were installed backwards. If you have a blade or two with a heavy bend backwards or forwards, heat the blade with a heat gun or blow dryer until it is extremely hot without melting. While the blade is still hot, put some weight in the middle of the bed and let it completely cool in an opposite bent direction. All Raptor Blades have a twist from the butt to the tip and this is normal. Bent blades, however, usually do not create a problem.

Click here for the Raptor Generation 4 Blade Installation Diagram
Raptor Generation 4 Blade Installation Instructions

Wind Turbine Siting:

Turbulence will severely reduce power output and is usually caused by structures swirling and blocking the wind before striking the blades and tail (usually noticed by erratic left to right pivoting of the turbine on the tower, sometimes with heavy vibration). The best place for a turbine is well above the trees and structures (homes, buildings, etc.) closer than 200 feet away. Doubling the height of your tower can increase power by up to 34%.

Watch our video below on Where Not to Install a Wind Turbine

Usually in the heat of the summer there is very little wind. Fall, spring, winter and stormy seasons produce much more wind power. If you are having a hard time maintaining power production, another turbine or the addition of solar panels may be necessary.